Mon–Sun 8:00 AM – 9:00 PM · 24×7 emergency callouts
The invisible system that decides whether a fault is an inconvenience or a tragedy.
Earthing gives fault current a deliberate, low-resistance path back to source, so that a protective device sees it and disconnects. Without it, that path is whoever touches the appliance. We install and — just as importantly — we measure.
Ask most homeowners whether their property is earthed and they will say yes. Ask when the earth resistance was last measured and the answer is almost always never. This matters, because an earthing system is not a binary that either exists or does not. It has a resistance value, that value determines how much fault current can flow, and the fault current determines whether your MCB actually trips. An earth pit measuring 40 ohms is present, connected, and functionally useless.
Indian practice targets under 5 ohms for a domestic installation and under 1 ohm where sensitive equipment or three-phase commercial loads are involved. Achieving that in Surat's soil is straightforward when the pit is built correctly and maintained; it degrades over years as the soil around the electrode dries out and the salt-and-charcoal backfill leaches away. This is why we treat measurement as part of the service rather than an optional extra.
We install three types. Conventional plate earthing uses a 600×600 mm copper or GI plate set in a pit with alternating layers of salt and charcoal and a watering funnel to keep the surrounding soil conductive — the traditional, lowest-cost approach, needing seasonal watering. Pipe earthing uses a perforated GI pipe electrode, suits certain soil conditions and is easier to maintain. Chemical or maintenance-free earthing uses a factory-filled electrode with a conductive compound that holds moisture without watering, achieves lower and far more stable resistance, and is what we recommend for anything sensitive — three-phase supplies, lifts, servers, medical equipment or a home with substantial electronics.
Equally important is what the earth connects to. A pit is worthless if the earth continuity conductor is undersized, if bonding is missing, or if the sockets in your flat have an earth pin that is not actually connected to anything — something we find with depressing regularity when a socket analyser goes in. Every earthing job we do includes verifying earth continuity from the pit through the distribution board to the furthest socket on every circuit.
You receive a measured earth-resistance value from a calibrated tester, recorded on a certificate with the date, along with the continuity readings. If the value is above target we tell you why and what would bring it down — a second pit in parallel, a deeper electrode, or chemical backfill — rather than simply handing over a pit and calling it complete.
The difference between a job that lasts and one you will be calling about again is almost always in the details below.
A calibrated earth tester gives you a number in ohms on a dated certificate. Without that number, an earth pit is a hope.
Domestic installations targeted below 5 Ω and commercial below 1 Ω, with a stated plan if the soil will not allow it.
Chemical earthing electrodes hold low, stable resistance through dry season without seasonal watering.
A good pit means nothing if the earth pin at your socket is not connected. We verify every point with a socket analyser.
Removable cover and accessible test link so resistance can be re-measured in future without excavation.
Written cover on workmanship, with an optional annual re-measurement service to catch degradation early.
Every step is the same whether the job is worth ₹400 or ₹95,000.
Before quoting we measure the current earth resistance and check continuity — sometimes the existing pit only needs revival.
Soil type, moisture retention and available location determine electrode type, depth and whether one pit will suffice.
Pit excavated to depth, electrode set vertically, and backfilled in proper alternating layers of salt and charcoal or chemical compound.
Correctly sized earth conductor run to the distribution board, with bonding to metallic services where required.
Inspection chamber with removable cover and watering funnel built, and the surrounding area reinstated.
Earth resistance measured with a calibrated tester, socket continuity verified throughout, and a dated certificate issued.
Indicative 2026 ranges. You always receive a firm, itemised price after inspection — and nothing starts until you approve it.
| Item | Indicative price |
|---|---|
| Earth resistance test & reportCalibrated tester, dated certificate | ₹1,200 |
| Plate earthing (GI plate)Complete with chamber | ₹6,500 – ₹11,000 |
| Plate earthing (copper plate)Complete with chamber | ₹12,000 – ₹22,000 |
| Pipe earthingComplete with chamber | ₹7,500 – ₹13,000 |
| Chemical / maintenance-free earthingPer electrode | ₹14,000 – ₹28,000 |
| Earth pit revival & re-saltingExisting pit | ₹2,500 – ₹5,000 |
| Earth continuity repairDepends on circuit count | ₹1,500 – ₹6,000 |
Prices exclude civil repair and repainting where wall chasing is involved. Materials are charged at cost with original bills handed over, and there is no emergency markup on parts at any hour.
They surveyed the flat properly before quoting — actually walked around listing every appliance and worked out a load calculation. Two other contractors just gave me a per-point rate. The finished job came with a circuit schedule and test readings, and every MCB in the board is labelled. I finally know which breaker does what.
My RCCB had been tripping every night for two weeks and the previous electrician told me to replace the whole board. Ambey's technician isolated the circuits one at a time and found moisture in a terrace light point in about forty minutes. Fixed the fitting, sealed the entry, ₹1,400 total. Honest work.
Twenty-two year old flat with no RCCB and nobody had ever mentioned it. They explained the difference between MCB and RCCB in plain language, showed me the trip time on the tester after fitting, and gave me a certificate. Small job, done like it mattered.
The questions we are asked most often about this service, answered in full.
Same-day service in our primary area with no distance surcharge.
Tell us a little about the property and what you need. We will come back with an indicative figure and, where useful, arrange a free survey.
2–3 days scheduling in our primary service area. Licensed* electricians, instrument diagnosis, and 5 years on earth pit.